Lenti-XTM Packaging Single Shots (VSV-G)

Description

Lenti-X Packaging Single Shots VSV-G provide an extremely simple and consistent one-step method for producing high-titer lentivirus. No additional transfection reagent is needed because Lenti-X Packaging Single Shots VSV-G consist of pre-aliquoted, lyophilized, single tubes of XfectTransfection Reagent premixed with an optimized formulation of VSV-G pseudotyped Lenti-X lentiviral packaging plasmids. High-titer virus is produced by simply reconstituting this mixture with your lentiviral vector of choice in sterile water and adding it to 293T cells, e.g., Lenti-X 293T Cells Cat. # 632180 , in a 10 cm dish. Our products are to be used forResearch Use Only. They may not be used for any other purpose, including, but not limited to, use in humans, therapeutic or diagnostic use, or commercial use of any kind. Our products may not be transferred to third parties, resold, modified for resale, or used to manufacture commercial products or to provide a service to third parties without our prior written approval. Back Back Consistent, high-efficiency transfections lead to high titers.A lentiviral vector containing the ZsGreen1 gene was packaged according to the Lenti-X single shots protocol in four independent experiments. Briefly, 7 mug of pLVX-ZsGreen1 plasmid was added to each of four Lenti-X single shots; the tubes were vortexed for 20 sec and incubated at room temperature for 10 min. Then, the mixture was added to cultured Lenti-X 293T cells that were approximately 80 % confluent. 48 hours after transfection, the cells were imaged by fluorescence microscopy Panel A, top and light microscopy Panel A, bottom . After images were taken, the supernatant was harvested and used infect HT1080 cells for titer determination Panel B, IFU/ml . Back High-titer virus was produced regardless of the lentiviral vector backbone with Lenti-X packaging single shots.A CMV ZsGreen1 expression cassette was cloned into several lentiviral vector backbones. These vectors were then packaged into lentivirus using the Lenti-X packaging single shots following the provided protocol. Briefly, 7 mug of pLVX-ZsGreen1 plasmid was added to each of four Lenti-X single shots, and the tubes were vortexed for 20 sec and incubated at room temperature for 10 min. Then, the mixture was added to cultured Lenti-X 293T cells that were approximately 80 % confluent. After 48 hours, titer was determined using several methods. To determine infectivity, the supernatant was harvested and used to infect HT1080 cells Flow Cytometry . Harvested viral supernatants were also analyzed by RT-PCR to quantify viral genome copies qRT-PCR, Lenti-X qRT-PCR Titration Kit , ELISA to measure p24 p24 ELISA, Lenti-X p24 Rapid Titer Kit , and by a rapid lentiviral detection method Lenti-X GoStix . Back A comparison of fourth- and third-generation lentiviral packaging systems .Our Lenti-X Packaging single shots utilize a packaging system that consists of five separate components Panel A , mixed in proprietary proportions for optimized packaging activity. The separation of thegag,pol, andenvgenes effectively reduces the incidence of RCL Wuet al., 2000 . High levels of expression of essential viral components are driven by the Tet-Off and Tat transactivators, which induce a cascade of expression that results in high titers of lentivirus. Thepolgene is fused tovprto ensure transport of the reverse transcriptase/integrase protein into the recombinant lentiviral particle. Not all vector elements are shown. Other 3rd generation lentiviral packaging systems Panel B generate lower titers, do not contain separategagandpolsequences, and do not use a transactivation cascade mechanism. Back